GENERAL TOOLS

Ergonomic handle The tip design cradles the return spring to keep it from sliding off. Heat treated material and extra-long shaft provides stren...

Quickly restore threads to near new condition without expensive thread cutting equipment. Replaceable V-Pads and dies. Use for 1-1/4” to 5” O.D IN...

Low Profile Sockets for Better Access Set includes: KDT3932D - 32mm, KDT3933D - 27mm, KDT3934D - 36mm, KDT3935 - 24mm and KDT3939D - 38mm Oil Filt...

The puller will spread from 2" to 7-3/4" Block is 8-1/4" wide, and its forcing screw is 3/4" - 16 x 11-5/8" long Accommodates any cap screws up to...

**Easily remove tough grease, oils and dirt with this heavy duty hand cleaner**Removes Tough Grime, Without WateHand cleaner features a pumice-fre...

With convenient hot circuit indicator, red ready light glows when starter switch is connected to a hot circuit; light goes off when switch is depr...

Strong but flexible Specifically engineered sizes designed for small round connector types Diameter sizes range from .030" to .120" and 5" lo...

Highly durable with mild abrasive coating  Pivoting-handle design for added versatility Works for both male and female connectors on flat (spad...

Step Plate 205-D015 D80L-630-4 8060 Part of 205-DS011 Outer Dimension 1 3/8", Inner Dimension 1 1/8". Automatic Transaxle/Transmission Reference M...

Hydraulic Hollow Center Cylinder with 30 tons of force makes kingpin and brake anchor pin removal easy Five special collars and two pins allow thi...

Designed to remove broken studs, bolts, socket screws and fittings for high torque applications Aggressive left hand spiral design for extra gripp...

Extractors quickly and easily remove broken screws, pipes, bolts and studs Manufactured with heat-treated chrome-moly steel Long wear and durabili...

Only dye needed for engine oil, transmission fluid, power steering fluid, hydraulic oil, gasoline and diesel fuel Service stickers included Works...

Offers maximum working pressure of 16 bar (232 PSI) and precise air flow control The body is molded in hardwearing POM for extra durability and lo...

Use with 1" square drive impact wrench Metric sizes for Isuzu, Hino, Mitsubishi, Fuso, White Volvo, Mack Midliner and other imports Fractional siz...

TU-15-11A Diesel Compression Test Adapter Tool Used with J-6692-B Compression Test Gauge Includes short injector, long injector and hold-down bar w...

Cold-forged twin hammer impact mechanism and motor deliver 2,000 ft-lbs of Nut Busting Torque, durability, and efficiency Steel hammer case stands...

This is located in a very tight location Tool is built to bottom out on the hex so it does not put torque on the connector in case it can be reuse...

Hook and point design Made of chrome vanadium steel Machined and hardened tips Lifetime guaranteed

For extracting and dispensing fluids such as diesel fuel, motor oil, brake fluid, transmission fluid, rear differential fluid, and coolant in vehi...

149-2955 Seal Protector Application: 3126B

1P-5564 M3572 1100 3208 Compression Test Adapter Alternative Used with J-6692-B 1/4 NPT Fitting Applications: Caterpillar 1100 & 3208 Series; J...

1U-6673 Fuel Ratio Control Adjusting and Synchronizing Wrench Applications: 3114, 3116, 3126

TU-15-42 3116 Compression Test Adapter Injector adapter with quick disconnect for Caterpillar 3116 engines. Used with J-6692-B Compression Test Gauge

230-6284 Locating Pin Tool Used for fuel system tune up Applications: 3054C Engine, Machine Model 416E/420E

238-9586 Engine Barring Tool

142-8278 Swage Tool Applications: 3114, 3116 and 3126 Engines

Crankshaft Oil Seal Remover J-35993 Applications: Detroit Diesel Series 60

ZTSE4642 Injector Sleeve Installer Tool Alt ST-253 Stallion Used to install the injector sleeves into the cylinder head. This tool typically works ...

VM.10358B VM.10358A Fuel Injector Puller Tool Alt ST-303 2011 (Grand Cherokee) - System (14 - Fuel System) 2012 (300, 300C, Charger, Magnum, Grand...

2025002090 3.6L 2016+ Right Timing Chain Tensioner Holding Tool Alt ST-314 Applications: Applications of 3.6L Pentastar 2016 - Current

ST-1229 Cummins Cylinder Liner Driver  

Can be used as a contact as well as a non-contact tachometer Four styles of contact adapter tips clip easily to the top of the phototach Infrared ...

12-892-01AU EGR Cooler Alignment Tool Alt ST-275 Applications: 2010 MaxxForce 11 , 2010 MaxxForce 13 , 2013 N13 w/SCR , 9000i Series , LoneStar , P...

09260-39021-01 Fuel Injector Seal Installer Tool Set Alt ST-S919 Includes High Quality Stallion Equivalents of 09261-03020-01 & 09261-03011-01

J-41479-B Rear Oil Seal Installer Set Alt Stallion ST-197 Applications: 4.8L, 5.3L, 5.7L, 6.0L, 6.2L and more If you have the following seal/re...

Applications: High Feature V6 (2.8L, 3.0L, 3.6L) The camshafts must be held at TDC to properly set timing, especially once the inner timing chain i...

EN-47988 Serpentine Belt Tension Unloader Tool Alt Stallion ST-176 The EN-47988 is required to release the accessory drive belt tension. Minimal ...

7.3L Powerstroke Front Crankshaft Seal Wear Ring Remover Alt Stallion ST-202 This tool works on all 7.3L Powerstroke Diesel Engines. Workshop man...

303-762 ZTSE4517 6.0L Ford Powerstroke Front Crankshaft Seal Wear Ring Remover Alt Stallion ST-130 Vehicles Including Ford Super Duty Diesel F-25...

303-517 / T95P-6701-CH 6.8L 5.8L 5.4L 4.6L Crankshaft Rear Oil Slinger Installer Adapter Alt ST-201 Stallion Used with ST-200 Applications: Ford...

303-1655 3.5L High-Performance Engine Camshaft Alignment Tool Pair Alt ST-S922-B Used for 3.5L Engine Upgrade. Ford Expedition equipped with 3...

303-1655 3.5L High-Performance Engine Camshaft Alignment Tool Alt ST-248 Used for 3.5L Engine Upgrade. Ford Expedition equipped with 3.5L EcoB...

Stallion ST-101 3V Valve Spring Compressor - 303-1039 Alt If you are changing springs you will want to add the 16mm air hold tool if you have the S...

205-380 T97T-4946-B 10.25" 10.5" Traction Lock Differential Gauge Tool Alt ST-260 To use this mandrel you must purchase 205-135 or ST-171. Rear Dr...

205-110 Gauge Block T76P-4020-A10 MB990905-4-01 Alt Stallion ST-185 1.7" Applications: Ford, Mitsubishi, Chrysler Rear Drive Axle/Differential —...

G-Style plugs are case hardened steel, plated to resist rust Maximum inlet pressure: 300 PSI Maximum temperature: 250 degrees F Air flow: 99 SCFM

5 to 5 1/4 Piston Ring Band  Must be used with Plier MI-KAS980A