GENERAL TOOLS

Works on 1994-2003 7.3 diesel engine in Ford 3/4 and 1 ton trucks A complete kit with the tools you need to properly remove and install the rear m...

Test cylinder pressure on light-duty diesel trucks Dual scale gauge Wire reinforced hose 16 1/2" long Swivel end quick disconnect coupler Comes in...

Socket is built to have the correct clearance for yoke and locknut assemblies on a variety of truck transmissions and differentials Socket has 3" ...

Socket is built to have the correct clearance for yoke and locknut assemblies on a variety of truck transmissions and differentials Socket has 3" ...

3-1/2" 6 point locknut socket Wheel bearing locknuts are easy to remove or install with these specially designed sockets Sockets are made of high-...

Manually operated, screw-powered device removes cylinder sleeves from most truck, bus and tractor engines Handles wet and dry sleeves, you won't n...

2-1/4" 6 point locknut socket Wheel bearing locknuts are easy to remove or install with these specially designed sockets Sockets are made of high-...

2-5/8" 6 point locknut socket Wheel bearing locknuts are easy to remove or install with these specially designed sockets Sockets are made of high-...

Double-sided. Used with the 29090 Truck Anchor Pin Bushing Kit to remove and install anchor pin bushings and stuck anchor pins.

2-9/16" 8 point locknut socket Wheel bearing locknuts are easy to remove or install with these specially designed sockets Sockets are made of high...

3-1/4" 6 point locknut socket Wheel bearing locknuts are easy to remove or install with these specially designed sockets Sockets are made of high-...

3-1/2" 8 point locknut socket Wheel bearing locknuts are easy to remove or install with these specially designed sockets Sockets are made of high-...

4-1/8" 6 point locknut socket Wheel bearing locknuts are easy to remove or install with these specially designed sockets Sockets are made of high-...

Accommodates a 1/2" drive impact wrench Services GM, Ford and Chrysler built 1-ton 2WD and 4WD trucks Also works on medium-duty Class 2 through Cl...

1/2 in. square drive Use on 1973-81 GM 3/4- and 1-ton trucks Use on 1978-84 ford F-series H.D. 3/4 and 1-ton 4WD trucks Made from high strength st...

Extra thin wall deep length impact socket for removing/installing transmission and differential and yoke locknuts* on a wide variety of trucks Mad...

Low profile, double-ended tools disconnect fuel lines on many Chrysler, Ford, and GM vehicles Useful for removing the fuel supply line from the se...

Socket is 2” Long The drive size is 3/4" Fits 2-9/64” ball joints Similar to Miller Tools No. C-3561 OTC8034

Services 3/4 and 1 ton American made trucks with 4,6, and 8 bolt patterns.  Mega Hammer 4-6-8 Bolt Pattern

Special low-profile design works in close quarters Designed to access the center port on GM fuel tank sending unit For 3/8" and 1/2" applications;...

Designed to service Ford 4.6L 3V V8 engines used in 05-10 Mustang, 06-10 Explorer, 09 F-Series trucks Designed to service Ford 5.4L 3V V8 engines ...

Patented Design allows tool to be mounted to suspension instead of needing to be held by technician during bushing service Specially designed push...

Precise OEM design Metal construction for durability Used to disconnect high-pressure oil rail supply line Used on the Ford 6.0L diesel engine Mus...

Especially designed to accommodate the 1-11/16 in. (43mm) wheel bearing retaining nut which is recessed into the hub Since the retaining nut is re...

For use with 1/2" ratchet or breaker bar Works on 1990-93 Dodge trucks with Dana 60 manual hubs Also available as part of 4542 7-Piece Wheel Beari...

Separating Pitman arms on cars and light trucks is quick and easy with this wedge and an appropriate sized hammer 11" long and has a 1-1/8" for sp...

Disconnects the hydraulic clutch line from the clutch slave cylinder on the following vehicles with manual transmissions and hydraulic clutches: 1...

Adjustable with special replaceable forged jaws Two clamp bolts lock jaws on Pitman arm Can perform other pulling jobs Services cars and light tru...

54 mm hex socket 1/2" square drive end Permits use of a torque wrench 1982-newer Toyota trucks, models FJ, LN, RN

Services 1995-1996 Ford F-series 1/2 ton trucks and full size Bronco with automatic hubs 1/2" square drive

Removes clogged or stuck diesel injector seals 1 Kg (2.2 lbs) slide hammer removes the most difficult seals Slide hammer designed with integrated ...

Designed to install frost plugs in liquid-cooled gas and diesel engines found in automobiles, trucks, SUV, agricultural equipment, and constructio...

Use to loosen or tighten injection pump retaining bolts whenever pump timing adjustment or pump service is required Services 1996–1999 GM full-siz...

Made from high-quality materials to ensure long-lasting performance and durability Designed for use with F-Series Super Duty trucks and 6.0L Power...

Feature a 1/2" square drive 2 9/16" rounded hex locknut socket Can be used with an extension and torque wrench for accurate tightening Works on 19...

Can be used with an extension and torque wrench for accurate tightening Works on 3/4- and 1 ton Ford F-250 and F-350 trucks with automatic locking...

Designed to withstand the force of a 3/4" drive impact wrench This rugged socket makes truck tie-rod end removal quick and simple Works on inner a...

Spread between jaw tips: 1-5/16 in. Adjustable with special replaceable forged jaws Two clamp bolts lock jaws on Pitman arm

It can be used with several different attachments depending on the job Has 9-1/2" legs Maximum reach 11-1/2" with a spread of 3-1/8"-11-3/4" Screw...

Designed to remove and install frost plugs used in liquid-cooled gas and disel engines found in automobiles, trucks, SUVs, agricultural equipment ...

Labor intensive removal of steering sector is not necessary Compact design of puller allows easy access to the Pitman arm Live center on forcing s...

Heavy duty puller works on most cars and trucks Designed to work on even the most stubborn Pitman arm pulling jobs Position puller jaws over Pitma...

Services 1995-1998 Ford F-series 3/4 and 1 ton trucks with automatic hubs 1/2" square drive Wt., 2 lbs., 2 oz.

The set contains 11 drivers for use on both cars and trucks up to 1 ton Includes two handles, one for hammering and one for use with an air hammer...

Removes and installs injectors without damaging the injector or cylinder head Kit is manufactured to accept a standard 3/8" drive Application: 199...

2-3/4" 6 point locknut socket Wheel bearing locknuts are easy to remove or install with these specially designed sockets Sockets are made of high-...

Removes stubborn hubs when nothing else will Two methods of removal which includes removal of the hub with the aid of the power steering, and remo...

Quickly diagnose, repair and restore truck and trailer harness connections Includes 6 Pin Tester, Pin Cleaner/Resizer and chemical contact enhance...